How To Set Up Water Softener System

Download Article

Download Commodity

Basis water that has excessive minerals in it is called hard water. Difficult water doesn't dissolve lather and detergent very well and leaves behind scales, which stain toilets and sinks. Installing a water softener volition reduce the amount of minerals, and provide your house with soft water.

Steps Download Article

one

Read all the directions that came with your water softener earlier you lot began the installation.
2

Shut off the water to the house and turn off the ability to the hot water heater. ^[1]

Advertisement
3

Plough on all the faucets and exterior hoses to drain your water lines before yous put in a h2o softener. ^[2]
4

Position your water conditioner in a dry, safety area that is level. Most water softeners take ii tanks, and you need to ready them next to each other.
5

Measure the length between the common cold h2o line and the bypass ports on the h2o softener tank with a measuring record. Cut a piece of copper tubing that length, and solder fittings on the ends. Water conditioner installation includes some soldering work.^[iii]
6

Follow the manufacturer's management to install the discharge tube on the water softener head.
vii

Run the overflow tube that'south attached to the side of the h2o conditioner tank and the discharge tube to a drain. With h2o softener installation, you must provide drainage.^[4]
8

Put the bypass valve on to the water conditioner's head valve. Adjust the screws on the stainless steel clamps with a screwdriver to seat the valve. When you lot install a h2o softener, exist sure to accept all your tools prepare.
9

Connect the copper tubing that delivers water to the bypass valve. Use a wrench to tighten the supply tube nuts. When you lot put in a water softener, don't wrench the nuts too tight.
10
Attach the copper tubing from the water conditioner to the water lines.
- Scrub the fittings and the pipes with steel wool. When installing a water conditioner, you'll need to solder the fitting to the pipes.
- Solder the fittings together past applying flux and melting it with a propane torch.
eleven

Turn your electric heater and the water to the firm dorsum on.
12

Plug the control valve in and put most 4 gallons (xv.142 liters) of water into the brine tank. H2o softener installation includes setting up the brine tank, and you'll need to add 40 lbs. (18.144 kg) of potassium chloride common salt or sodium chloride to the unit.^[5]
xiii

Put your conditioner into the backwash stage and set the bypass valve to the service position. To put in a water softener, open the water supply valve to the 1/iv position to let oxygen run from the drain line.
14

Turn the water supply valve completely on when a steady stream of water appears at the drain.
fifteen

Allow the conditioner run through the complete backwash cycle when installing a water softener.
16

Test the system for leaks. If any water is escaping, check your soldering and the nuts. Re-solder or tighten nuts to repair any leaks.

Add New Question

Question

How tin I drain softener without going through the septic tank?

Your septic tank takes all the drain h2o. Why do you non desire information technology going to the septic tank?
Question

Does the water softener need to exist close to the water heater?

No, just commonly they are close anyways since the appliances are normally in a closet where all these things are installed. Otherwise, it would not modify operation to accept it elsewhere.
Question

What if I don't have a drain? Are there any other options?

WECO Sales Team

Community Reply

Collected calcium, iron and magnesium ions (hardness ions) in the bed need to be flushed out. This is done by sending h2o at a high menstruation rate though the bed in opposite management of normal water catamenia. So to answer your question, all water softeners must have a drain that backwashes the softener bed periodically. If you simply need particulate contaminants removed from water, you lot can become with a big blue cartridge filter instead of a softener and avoid the demand for a drain.
Question

Can I use my water heater as a supply line?

Best not to; it should become through softener first to preclude calcification and degradation of heater.
Question

How often does the water softener cycle?

That depends on the hardness of your h2o and the rated capacity of your softener.
Question

What is water softener backwash?

Backwash ordinarily refers to the cleaning bike of the h2o softener. This is when the water is being circulated in the reverse to clean out whatsoever debris.
Question

Tin I put h2o softener correct into my well (salt type softener)?

No! The water is softened past running through the resin bed of the water softener tank. The brine tank, which the salts are added to, is used to regenerate the ion substitution resin bed. The common salt is not added to the water to soften it.
Question

Tin can I put salt water softener directly into my well?

NO! The salt is to reclaim the resin chaplet inside of the softener tank. The table salt breaks the calcium chloride (the stuff in the well water) from the plastic resin chaplet inside of the tank.
Question

If I put a water softener outside next to your business firm, exercise I need to enclose it in a cabinet, or can it be exposed to the elements?

Y'all should put the softener inside the house because in the cold weather the water will freeze.
Question

How practise I set the timer to work during the dark on my water softener?

Most softeners regen at 2:00 AM on the days they regen. You just need to make certain the clock is set correctly so that the softener knows when 2:00 AM is. See your owners manual for the fourth dimension it regens.